 |
dphy
Vitis Drivers API Documentation
|
|
dphy
Vitis Drivers API Documentation
|
Macros | |
| #define | XDPHY_HW_H_ |
| Prevent circular inclusions by using protection macros. More... | |
Device registers | |
| #define | XDPHY_CTRL_REG_OFFSET 0x00000000 |
| Control Register. More... | |
| #define | XDPHY_HSEXIT_IDELAY_REG_OFFSET 0x00000004 |
| IDelay Tap per lane for Rx Register. More... | |
| #define | XDPHY_INIT_REG_OFFSET 0x00000008 |
| Initialization Timer Register. More... | |
| #define | XDPHY_WAKEUP_REG_OFFSET 0x0000000C |
| Wakeup Timer for ULPS exit Register. More... | |
| #define | XDPHY_HSTIMEOUT_REG_OFFSET 0x00000010 |
| Watchdog timeout in HS mode Register. More... | |
| #define | XDPHY_ESCTIMEOUT_REG_OFFSET 0x00000014 |
| Goto Stop state on timeout timer Register. More... | |
| #define | XDPHY_CLSTATUS_REG_OFFSET 0x00000018 |
| Clk lane PHY error Status Register. More... | |
| #define | XDPHY_DL0STATUS_REG_OFFSET 0x0000001C |
| Data lane 0 PHY error Status Register. More... | |
| #define | XDPHY_DL1STATUS_REG_OFFSET 0x00000020 |
| Data lane 1 PHY error Status Register. More... | |
| #define | XDPHY_DL2STATUS_REG_OFFSET 0x00000024 |
| Data lane 2 PHY error Status Register. More... | |
| #define | XDPHY_DL3STATUS_REG_OFFSET 0x00000028 |
| Data lane 3 PHY error Status Register. More... | |
| #define | XDPHY_HSSETTLE_REG_OFFSET 0x00000030 |
| HS Settle Register L0. More... | |
| #define | XDPHY_IDELAY58_REG_OFFSET 0x00000034 |
| IDelay Tap per lane for Rx 4-7 Register. More... | |
| #define | XDPHY_HSSETTLE1_REG_OFFSET 0x00000048 |
| HS Settle Register L1. More... | |
| #define | XDPHY_HSSETTLE2_REG_OFFSET 0x0000004C |
| HS Settle Register L2. More... | |
| #define | XDPHY_HSSETTLE3_REG_OFFSET 0x00000050 |
| HS Settle Register L3. More... | |
| #define | XDPHY_HSSETTLE4_REG_OFFSET 0x00000054 |
| HS Settle Register L4. More... | |
| #define | XDPHY_HSSETTLE5_REG_OFFSET 0x00000058 |
| HS Settle Register L5. More... | |
| #define | XDPHY_HSSETTLE6_REG_OFFSET 0x0000005C |
| HS Settle Register L6. More... | |
| #define | XDPHY_HSSETTLE7_REG_OFFSET 0x00000060 |
| HS Settle Register L7. More... | |
| #define | XDPHY_DL4STATUS_REG_OFFSET 0x00000064 |
| Data lane 0 PHY error Status Register. More... | |
| #define | XDPHY_DL5STATUS_REG_OFFSET 0x00000068 |
| Data lane 1 PHY error Status Register. More... | |
| #define | XDPHY_DL6STATUS_REG_OFFSET 0x0000006C |
| Data lane 2 PHY error Status Register. More... | |
| #define | XDPHY_DL7STATUS_REG_OFFSET 0x00000070 |
| Data lane 3 PHY error Status Register. More... | |
Bitmasks and offsets of XDPHY_CTRL_REG_OFFSET register | |
This register is used for the enabling/disabling and resetting the DPHY | |
| #define | XDPHY_CTRL_REG_SOFTRESET_MASK 0x00000001 |
| Soft Reset. More... | |
| #define | XDPHY_CTRL_REG_DPHYEN_MASK 0x00000002 |
| Enable/Disable controller. More... | |
| #define | XDPHY_CTRL_REG_SOFTRESET_OFFSET 0 |
| Bit offset for Soft Reset. More... | |
| #define | XDPHY_CTRL_REG_DPHYEN_OFFSET 1 |
| Bit offset for DPHY Enable. More... | |
Bitmasks and offsets of XDPHY_HSEXIT_IDELAY_REG_OFFSET register | |
This register in RX mode acts like IDELAY. In IDELAY mode, it is used to calibrate input delay per lane | |
| #define | XDPHY_HSEXIT_IDELAY_REG_TAP_MASK 0x1F1F1F1F |
| used to set the IDELAY TAP value for all lanes More... | |
Bitmasks and offsets of XDPHY_INIT_REG_OFFSET register | |
This register is used for lane Initialization. Recommended to use 1ms or longer in for TX mode and 200us-500us for RX mode | |
| #define | XDPHY_INIT_REG_VAL_MASK 0xFFFFFFFF |
| Init Timer value in ns. More... | |
| #define | XDPHY_INIT_REG_VAL_OFFSET 0 |
| Bit offset for Init Timer. More... | |
Bitmask and offset of XDPHY_WAKEUP_REG_OFFSET register | |
| #define | XDPHY_WAKEUP_REG_VAL_MASK 0xFFFFFFFF |
| Wakeup timer value. More... | |
| #define | XDPHY_WAKEUP_REG_VAL_OFFSET 0 |
| Bit offset for Wakeup value. More... | |
Bitmask and offset of XDPHY_HSTIMEOUT_REG_OFFSET register | |
This register is used to program watchdog timer in high speed mode. Default value is 65541. Valid range 1000-65541. | |
| #define | XDPHY_HSTIMEOUT_REG_TIMEOUT_MASK 0xFFFFFFFF |
| HS_T/RX_TIMEOUT Received. More... | |
| #define | XDPHY_HSTIMEOUT_REG_TIMEOUT_OFFSET 0 |
| Bit offset for Timeout. More... | |
Bitmask and offset of XDPHY_ESCTIMEOUT_REG_OFFSET register | |
This register contains Rx Data Lanes timeout for watchdog timer in escape mode. | |
| #define | XDPHY_ESCTIMEOUT_REG_VAL_MASK 0xFFFFFFFF |
| Escape Timout Value. More... | |
| #define | XDPHY_ESCTIMEOUT_REG_VAL_OFFSET 0 |
| Bit offset for Escape Timeout. More... | |
Bitmask and offset of XDPHY_CLSTATUS_REG_OFFSET register | |
This register contains the clock lane status and state machine control. | |
| #define | XDPHY_CLSTATUS_REG_ERRCTRL_MASK 0x00000020 |
| Clock lane control error. More... | |
| #define | XDPHY_CLSTATUS_REG_STOPSTATE_MASK 0x00000010 |
| Clock lane stop state. More... | |
| #define | XDPHY_CLSTATUS_REG_INITDONE_MASK 0x00000008 |
| Initialization done bit. More... | |
| #define | XDPHY_CLSTATUS_REG_ULPS_MASK 0x00000004 |
| Set in ULPS mode. More... | |
| #define | XDPHY_CLSTATUS_REG_MODE_MASK 0x00000003 |
| Low, High, Esc mode. More... | |
| #define | XDPHY_CLSTATUS_ALLMASK |
| #define | XDPHY_CLSTATUS_REG_ERRCTRL_OFFSET 5 |
| Bit offset for Control Error on Clock. More... | |
| #define | XDPHY_CLSTATUS_REG_STOPSTATE_OFFSET 4 |
| Bit offset for Stop State on Clock. More... | |
| #define | XDPHY_CLSTATUS_REG_INITDONE_OFFSET 3 |
| Bit offset for Initialization Done. More... | |
| #define | XDPHY_CLSTATUS_REG_ULPS_OFFSET 2 |
| Bit offset for ULPS. More... | |
| #define | XDPHY_CLSTATUS_REG_MODE_OFFSET 0 |
| Bit offset for Mode bits. More... | |
Bitmasks and offsets of XDPHY_DLxSTATUS_REG_OFFSET register | |
| #define | XDPHY_DLXSTATUS_REG_PACKETCOUNT_MASK 0xFFFF0000 |
| Packet Count. More... | |
| #define | XDPHY_DLXSTATUS_REG_CALIB_STATUS_MASK 0x00000100 |
| Calib status. More... | |
| #define | XDPHY_DLXSTATUS_REG_CALIB_COMPLETE_MASK 0x00000080 |
| Calib complete. More... | |
| #define | XDPHY_DLXSTATUS_REG_STOP_MASK 0x00000040 |
| Stop State on data lane. More... | |
| #define | XDPHY_DLXSTATUS_REG_ESCABRT_MASK 0x00000020 |
| Set on Data Lane Esc timeout occurs. More... | |
| #define | XDPHY_DLXSTATUS_REG_HSABRT_MASK 0x00000010 |
| Set on Data Lane HS timeout. More... | |
| #define | XDPHY_DLXSTATUS_REG_INITDONE_MASK 0x00000008 |
| Set after initialization. More... | |
| #define | XDPHY_DLXSTATUS_REG_ULPS_MASK 0x00000004 |
| Set when DPHY in ULPS mode. More... | |
| #define | XDPHY_DLXSTATUS_REG_MODE_MASK 0x00000003 |
| Control Mode (Esc, Low, High) of Data Lane. More... | |
| #define | XDPHY_DLXSTATUS_ALLMASK |
| #define | XDPHY_DLXSTATUS_REG_PACKCOUNT_OFFSET 16 |
| Bit offset packet count. More... | |
| #define | XDPHY_DLXSTATUS_REG_CALIB_STATUS_OFFSET 8 |
| Bit offset calib status. More... | |
| #define | XDPHY_DLXSTATUS_REG_CALIB_COMPLETE_OFFSET 7 |
| Bit offset Calib complete. More... | |
| #define | XDPHY_DLXSTATUS_REG_STOP_OFFSET 6 |
| Bit offset for Stop State. More... | |
| #define | XDPHY_DLXSTATUS_REG_ESCABRT_OFFSET 5 |
| Bit offset for Escape Abort. More... | |
| #define | XDPHY_DLXSTATUS_REG_HSABRT_OFFSET 4 |
| Bit offset for High Speed Abort. More... | |
| #define | XDPHY_DLXSTATUS_REG_INITDONE_OFFSET 3 |
| Bit offset for Initialization done. More... | |
| #define | XDPHY_DLXSTATUS_REG_ULPS_OFFSET 2 |
| Bit offset for ULPS. More... | |
| #define | XDPHY_DLXSTATUS_REG_MODE_OFFSET 0 |
| Bit offset for Modes. More... | |
Bitmask and offset of XDPHY_HSSETTLE_REG_OFFSET register | |
This register is used to program the HS SETTLE register. Default value is 135 + 10UI. | |
| #define | XDPHY_HSSETTLE_REG_TIMEOUT_MASK 0x1FF |
| HS_SETTLE value. More... | |
| #define | XDPHY_HSSETTLE_REG_TIMEOUT_OFFSET 0 |
| Bit offset for HS_SETTLE. More... | |
| #define XDPHY_CLSTATUS_REG_ERRCTRL_MASK 0x00000020 |
Clock lane control error.
Only for RX
| #define XDPHY_CLSTATUS_REG_ERRCTRL_OFFSET 5 |
Bit offset for Control Error on Clock.
| #define XDPHY_CLSTATUS_REG_INITDONE_MASK 0x00000008 |
Initialization done bit.
| #define XDPHY_CLSTATUS_REG_INITDONE_OFFSET 3 |
Bit offset for Initialization Done.
| #define XDPHY_CLSTATUS_REG_MODE_MASK 0x00000003 |
Low, High, Esc mode.
Referenced by XDphy_GetClkLaneMode().
| #define XDPHY_CLSTATUS_REG_MODE_OFFSET 0 |
Bit offset for Mode bits.
| #define XDPHY_CLSTATUS_REG_OFFSET 0x00000018 |
Clk lane PHY error Status Register.
Referenced by XDphy_GetClkLaneStatus(), and XDphy_GetInfo().
| #define XDPHY_CLSTATUS_REG_STOPSTATE_MASK 0x00000010 |
Clock lane stop state.
| #define XDPHY_CLSTATUS_REG_STOPSTATE_OFFSET 4 |
Bit offset for Stop State on Clock.
| #define XDPHY_CLSTATUS_REG_ULPS_MASK 0x00000004 |
Set in ULPS mode.
| #define XDPHY_CLSTATUS_REG_ULPS_OFFSET 2 |
Bit offset for ULPS.
| #define XDPHY_CTRL_REG_DPHYEN_MASK 0x00000002 |
Enable/Disable controller.
Referenced by XDphy_Activate().
| #define XDPHY_CTRL_REG_DPHYEN_OFFSET 1 |
Bit offset for DPHY Enable.
| #define XDPHY_CTRL_REG_OFFSET 0x00000000 |
Control Register.
Referenced by XDphy_Activate(), and XDphy_Reset().
| #define XDPHY_CTRL_REG_SOFTRESET_MASK 0x00000001 |
Soft Reset.
Referenced by XDphy_Reset().
| #define XDPHY_CTRL_REG_SOFTRESET_OFFSET 0 |
Bit offset for Soft Reset.
| #define XDPHY_DL0STATUS_REG_OFFSET 0x0000001C |
Data lane 0 PHY error Status Register.
Referenced by XDphy_ClearDataLane(), XDphy_GetDataLaneStatus(), XDphy_GetDLCalibStatus(), XDphy_GetInfo(), and XDphy_GetPacketCount().
| #define XDPHY_DL1STATUS_REG_OFFSET 0x00000020 |
Data lane 1 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL2STATUS_REG_OFFSET 0x00000024 |
Data lane 2 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL3STATUS_REG_OFFSET 0x00000028 |
Data lane 3 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL4STATUS_REG_OFFSET 0x00000064 |
Data lane 0 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL5STATUS_REG_OFFSET 0x00000068 |
Data lane 1 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL6STATUS_REG_OFFSET 0x0000006C |
Data lane 2 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DL7STATUS_REG_OFFSET 0x00000070 |
Data lane 3 PHY error Status Register.
Referenced by XDphy_GetInfo().
| #define XDPHY_DLXSTATUS_REG_CALIB_COMPLETE_MASK 0x00000080 |
Calib complete.
Referenced by XDphy_GetDLCalibStatus().
| #define XDPHY_DLXSTATUS_REG_CALIB_COMPLETE_OFFSET 7 |
Bit offset Calib complete.
| #define XDPHY_DLXSTATUS_REG_CALIB_STATUS_MASK 0x00000100 |
Calib status.
Referenced by XDphy_GetDLCalibStatus().
| #define XDPHY_DLXSTATUS_REG_CALIB_STATUS_OFFSET 8 |
Bit offset calib status.
| #define XDPHY_DLXSTATUS_REG_ESCABRT_MASK 0x00000020 |
Set on Data Lane Esc timeout occurs.
Referenced by XDphy_ClearDataLane().
| #define XDPHY_DLXSTATUS_REG_ESCABRT_OFFSET 5 |
Bit offset for Escape Abort.
| #define XDPHY_DLXSTATUS_REG_HSABRT_MASK 0x00000010 |
Set on Data Lane HS timeout.
Referenced by XDphy_ClearDataLane().
| #define XDPHY_DLXSTATUS_REG_HSABRT_OFFSET 4 |
Bit offset for High Speed Abort.
| #define XDPHY_DLXSTATUS_REG_INITDONE_MASK 0x00000008 |
Set after initialization.
| #define XDPHY_DLXSTATUS_REG_INITDONE_OFFSET 3 |
Bit offset for Initialization done.
| #define XDPHY_DLXSTATUS_REG_MODE_MASK 0x00000003 |
Control Mode (Esc, Low, High) of Data Lane.
Referenced by XDphy_GetDataLaneMode().
| #define XDPHY_DLXSTATUS_REG_MODE_OFFSET 0 |
Bit offset for Modes.
| #define XDPHY_DLXSTATUS_REG_PACKCOUNT_OFFSET 16 |
Bit offset packet count.
Referenced by XDphy_GetPacketCount().
| #define XDPHY_DLXSTATUS_REG_PACKETCOUNT_MASK 0xFFFF0000 |
Packet Count.
Referenced by XDphy_GetPacketCount().
| #define XDPHY_DLXSTATUS_REG_STOP_MASK 0x00000040 |
Stop State on data lane.
| #define XDPHY_DLXSTATUS_REG_STOP_OFFSET 6 |
Bit offset for Stop State.
| #define XDPHY_DLXSTATUS_REG_ULPS_MASK 0x00000004 |
Set when DPHY in ULPS mode.
| #define XDPHY_DLXSTATUS_REG_ULPS_OFFSET 2 |
Bit offset for ULPS.
| #define XDPHY_ESCTIMEOUT_REG_OFFSET 0x00000014 |
Goto Stop state on timeout timer Register.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_ESCTIMEOUT_REG_VAL_MASK 0xFFFFFFFF |
Escape Timout Value.
| #define XDPHY_ESCTIMEOUT_REG_VAL_OFFSET 0 |
Bit offset for Escape Timeout.
| #define XDPHY_HSEXIT_IDELAY_REG_OFFSET 0x00000004 |
IDelay Tap per lane for Rx Register.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSEXIT_IDELAY_REG_TAP_MASK 0x1F1F1F1F |
used to set the IDELAY TAP value for all lanes
Referenced by XDphy_Configure().
| #define XDPHY_HSSETTLE1_REG_OFFSET 0x00000048 |
HS Settle Register L1.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE2_REG_OFFSET 0x0000004C |
HS Settle Register L2.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE3_REG_OFFSET 0x00000050 |
HS Settle Register L3.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE4_REG_OFFSET 0x00000054 |
HS Settle Register L4.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE5_REG_OFFSET 0x00000058 |
HS Settle Register L5.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE6_REG_OFFSET 0x0000005C |
HS Settle Register L6.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE7_REG_OFFSET 0x00000060 |
HS Settle Register L7.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE_REG_OFFSET 0x00000030 |
HS Settle Register L0.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSSETTLE_REG_TIMEOUT_MASK 0x1FF |
HS_SETTLE value.
| #define XDPHY_HSSETTLE_REG_TIMEOUT_OFFSET 0 |
Bit offset for HS_SETTLE.
| #define XDPHY_HSTIMEOUT_REG_OFFSET 0x00000010 |
Watchdog timeout in HS mode Register.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_HSTIMEOUT_REG_TIMEOUT_MASK 0xFFFFFFFF |
HS_T/RX_TIMEOUT Received.
| #define XDPHY_HSTIMEOUT_REG_TIMEOUT_OFFSET 0 |
Bit offset for Timeout.
| #define XDPHY_HW_H_ |
Prevent circular inclusions by using protection macros.
| #define XDPHY_IDELAY58_REG_OFFSET 0x00000034 |
IDelay Tap per lane for Rx 4-7 Register.
Referenced by XDphy_Configure().
| #define XDPHY_INIT_REG_OFFSET 0x00000008 |
Initialization Timer Register.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_INIT_REG_VAL_MASK 0xFFFFFFFF |
Init Timer value in ns.
| #define XDPHY_INIT_REG_VAL_OFFSET 0 |
Bit offset for Init Timer.
| #define XDPHY_WAKEUP_REG_OFFSET 0x0000000C |
Wakeup Timer for ULPS exit Register.
Referenced by XDphy_Configure(), and XDphy_GetInfo().
| #define XDPHY_WAKEUP_REG_VAL_MASK 0xFFFFFFFF |
Wakeup timer value.
| #define XDPHY_WAKEUP_REG_VAL_OFFSET 0 |
Bit offset for Wakeup value.