# PIR sensor switch

This usermod-v2 modification allows the connection of a PIR sensor to switch on the LED strip when motion is detected. The switch-off occurs ten minutes after no more motion is detected.

_Story:_

I use the PIR Sensor to automatically turn on the WLED analog clock in my home office room when I am there.
The LED strip is switched [using a relay](https://github.com/Aircoookie/WLED/wiki/Control-a-relay-with-WLED) to keep the power consumption low when it is switched off.

## Webinterface

The info page in the web interface shows the items below

- the state of the sensor. By clicking on the state the sensor can be deactivated/activated. Changes persist after a reboot.
**I recommend to deactivate the sensor before an OTA update and activate it again afterwards**.
- the remaining time of the off timer. 

## JSON API

The usermod supports the following state changes:

| JSON key   | Value range | Description                     |
|------------|-------------|---------------------------------|
| PIRenabled | bool        | Deactivdate/activate the sensor |
| PIRoffSec  | 60 to 43200 | Off timer seconds               |

 Changes also persist after a reboot.

## Sensor connection

My setup uses an HC-SR501 sensor, a HC-SR505 should also work.

The usermod uses GPIO13 (D1 mini pin D7) for the sensor signal. 
[This example page](http://www.esp8266learning.com/wemos-mini-pir-sensor-example.php) describes how to connect the sensor.

Use the potentiometers on the sensor to set the time-delay to the minimum and the sensitivity to about half, or slightly above.

## Usermod installation

1. Copy the file `usermod_PIR_sensor_switch.h` to the `wled00` directory.
2. Register the usermod by adding `#include "usermod_PIR_sensor_switch.h"` in the top and `registerUsermod(new PIRsensorSwitch());` in the bottom of `usermods_list.cpp`.

Example **usermods_list.cpp**:

```cpp
#include "wled.h"
/*
 * Register your v2 usermods here!
 *   (for v1 usermods using just usermod.cpp, you can ignore this file)
 */

/*
 * Add/uncomment your usermod filename here (and once more below)
 * || || ||
 * \/ \/ \/
 */
//#include "usermod_v2_example.h"
//#include "usermod_temperature.h"
//#include "usermod_v2_empty.h"
#include "usermod_PIR_sensor_switch.h"

void registerUsermods()
{
  /*
   * Add your usermod class name here
   * || || ||
   * \/ \/ \/
   */
  //usermods.add(new MyExampleUsermod());
  //usermods.add(new UsermodTemperature());
  //usermods.add(new UsermodRenameMe());
  usermods.add(new PIRsensorSwitch());

}
```

## API to enable/disable the PIR sensor from outside. For example from another usermod.

The class provides the static method `PIRsensorSwitch* PIRsensorSwitch::GetInstance()` to get a pointer to the usermod object.

To query or change the PIR sensor state the methods `bool PIRsensorEnabled()` and `void EnablePIRsensor(bool enable)` are available. 

### There are two options to get access to the usermod instance:

1. Include `usermod_PIR_sensor_switch.h` **before** you include the other usermod in `usermods_list.cpp'

or

2. Use `#include "usermod_PIR_sensor_switch.h"` at the top of the `usermod.h` where you need it.

**Example usermod.h :**
```cpp
#include "wled.h"

#include "usermod_PIR_sensor_switch.h"

class MyUsermod : public Usermod {
  //...

  void togglePIRSensor() {
    if (PIRsensorSwitch::GetInstance() != nullptr) {
      PIRsensorSwitch::GetInstance()->EnablePIRsensor(!PIRsensorSwitch::GetInstance()->PIRsensorEnabled());
    }
  }
  //...
};
```

Have fun - @gegu